The best saw blades for wood for circular saw
We present the rating of saw blades for wood, compiled on the basis of positive feedback and characteristics, which will help you choose a proven cutting element that is fully consistent with upcoming work tasks.
The best saw blades with a diameter of 216-260 mm
Tooling for circular saws with a diameter of 216-260 mm is used for sawing boards, panels and bars of large cross-section. The maximum thickness of the workpiece should be slightly less than the radius of the disk (105-120 mm). But if the trimmed edge will be additionally processed or veneered, then it is allowed to cut a wooden element from two sides, combining two cuts, which doubles the maximum thickness. TOP saw blades for wood for circulars will show which equipment to choose for cutting wood of different moisture content and type of cut.
Dewalt DT1957 CONSTRUCT (250x30 mm; 48 ATB) - raw wood cut with nails
Sometimes there is a need to use especially durable saw blades that can easily cope with the load and do not lose the sharpness of a collision with nails. For such purposes, the Dewalt DT1957 CONSTRUCT saw blade is well suited. He contains 48 teeth with a sharpening angle of +10 degrees. It has a thick soldering at the tips of the teeth, providing a wide cut of 3 mm.
+ Pros Dewalt DT1957 CONSTRUCT (250x30 mm; 48 ATB)
- It cuts quickly and without jamming - a beam of 80x80 mm cuts through in 1 second.
- Excellent balancing - vibration is almost not felt, despite the tooling diameter of 250 mm.
- Holds sharpening well.
- Due to the thickness of the disk it does not lead to the side.
- On the disc itself, understandable instructions for sharpening teeth.
- Four large slots to compensate for thermal expansion.
- Cons Dewalt DT1957 CONSTRUCT (250x30 mm; 48 ATB)
- Due to the thick cut in the air, a lot of dust and a lot of chips remain on the floor.
- A sharpening angle of +10 degrees will have a worse effect on finished products.
- Poorly suitable for end cuts, when you need to make the exact size, and not just cut the beam into two parts.
Conclusion. It is not difficult to disassemble the building structures with the nails remaining in them with such equipment. The owner will be able to work for more than a year without significant loss of sharpness.
CMT 292.216.64M (216x30x2.8 / 1.8 mm; Z64) - especially for transverse cutting
Cross cutting of wood is not easy for every disc. The reason is the perpendicular arrangement of the fibers, which creates increased resistance. To understand which saw blade on wood is better in this case, you need to remember that it should have alternately chamfered teeth. This provides a soft impact and allows you to cut without strong burrs and chips.
CMT 292.216.64M (216x30x2.8 / 1.8 mm; Z64) - an excellent disk from the CMT brand of Italian origin. It has a diameter of 216 mm and 64 teeth, which are effective precisely with transverse cuts.
+ Pros CMT 292.216.64M (216x30x2.8 / 1.8 mm; Z64)
- Brazing on the teeth facilitates the fast cutting of even hard wood.
- Suitable for circulation saws of any manufacturer with a planting shaft with a diameter of 30 mm.
- Soldering keeps for a long time despite intensive use of circulars.
- When washing down the clypeus there are no explosions.
- The designations for which types of wood are best suited.
- Four hook-shaped cut-outs to compensate for expansion.
- Cons CMT 292.216.64M (216x30x2.8 / 1.8 mm; Z64)
- Some users received a curved disk (with a side runout), although there was no sign of damage on the package.
- So that there are no chips at all, it is necessary to enclose a zero insert as well.
- After it becomes dull it is very difficult to correct it yourself.
- If used on solid wood, it can slightly burn the end face.
Conclusion. An excellent choice for the production of a large volume of transverse cuts, which then do not have to be processed additionally - all the ends can be made in size the first time.
Makita B-04597 (260 mm; 30 mm; Z70) - clean cut
On the finishing blanks used in carpentry, it is important to cut the part exactly to the size so that there are no chips. For this, special saw blades for wood are used with the number of teeth from 70 pieces. This increases the cutting time, but promotes a gentle effect on the fibers and ensures high purity. The resulting edge does not need to be processed and can be mounted immediately, but the price of such disks is very high.
Makita B-04597 - Japanese disc with a diameter of 260 mm with 70 teeth. The cutting part has wide brazing and provides a clean cut thanks to the accurate action.
+ Pros Makita B-04597 (260 mm; 30 mm; Z70)
- Very clean cuts - especially on enameled surfaces.
- Suitable for the most moody finish coatings.
- When working, there is no ringing inherent in cheap cutting elements.
- Steel is hard to bend.
- Extra strong alloy.
- Suitable for any circular with a landing diameter of 30 mm and a rotation speed of up to 3670 rpm.
- Cons Makita B-04597 (260 mm; 30 mm; Z70)
- Cost over 4000 rubles.
- It has a decent weight, more than other models.
- The cut width of 2.3 mm can bite the snap with a slight tilt.
- It takes time to learn how to cut them without further processing.
Conclusion. This is a good choice for a workshop for the manufacture of furniture or other carpentry products. With five expansion cutouts and five winding grooves, the drive is characterized by low vibration and quiet operation.
The best saw blades with a diameter of 190 mm
Such equipment is used for cutting small wooden materials - boards and beams up to 75 mm high. The small size of the blade allows its use on compact circular hand saws. Here wood saw rating for circular saw with such diameters that are distinguished by quick cutting, cleanliness and fine cut, and are also suitable for chipboard and MDF.
Bosch 2.608.640.633 190x30 mm - quick cut
When cutting speed is a priority, discs with a small number of teeth are selected. This design has less resistance to rotation and contributes to the quick cutting of the material. But in view of the large distance between the cutting elements, the cut sides are rough and will have to be ground for finishing.
This disc from the German brand has 12 teeth with soldering and additional reinforcement on the back side. Leaves a cut of 2.6 mm wide.
+ Pluses Bosch 2.608.640.633 190x30 mm
- Suitable not only for wood, but also for aerated concrete, cement-based fiber boards.
- It even cuts boards with nails.
- Very low price and proven brand.
- Interacts with a tool issuing revolutions up to 4900 per minute.
- Cons Bosch 2.608.640.633 190x30 mm
- It can lead to metal, if you saw for a very long time - the disk has no cutouts for thermal expansion.
- The cut is not clean and needs further post-processing.
- It is more suitable for a longitudinal cut - on the transverse, fiber tears more strongly, which spoils the quality.
- Over time, it begins to cut more slowly - an estimated service life of 4 years.
- Sharpening looks dull (a feature of form and technology), so it is not possible to determine the quality in the store - you just need to install it on a saw and try.
Conclusion. This inexpensive disc is useful for quick cutting of wood when performing rough work.
CMT 272.190.42M (190x30 / 20 / 16x1.7 / 1.1 mm; Z42) - pure thin cut
Particularly thin cuts with clean edges require thin discs with a large number of teeth. Such equipment is used in the manufacture of furniture where accurate, precise cuts and a rational consumption of material are needed. But the payment for this is a thin section of the metal, which leads to biting or deformation. Work with such a disk should be more careful than others.
CMT 272.190.42M (190x30 / 20 / 16x1.7 / 1.1 mm; Z42) is a particularly thin disk with a thickness of 1.1 mm. It has 42 teeth and leaves a 1.7 mm wide cut.It is made directly in Italy and is intended for the finish cut.
+ Pros of CMT 272.190.42M (190x30 / 20 / 16x1.7 / 1.1 mm; Z42)
- Suitable for circular saws with revolutions up to 8000 per minute.
- Very quiet work.
- With it, it is easy to make longitudinal and transverse cuts in materials of various densities.
- Does not leave clumping fibers at the edges.
- Cons CMT 272.190.42M (190x30 / 20 / 16x1.7 / 1.1 mm; Z42)
- The price is much higher than analogues.
- Complex sharpening, which is not easy to restore at home.
- To install on some circular saws, adapter rings are needed - those that are included in the kit are thicker than the disk itself, so the latter does not clamp to the end.
- You can not rush much when performing a cut, otherwise it will be chipped.
Conclusion. Ideal for a furniture workshop. Will cut through OSB and similar materials as clean and precise as possible. Eight slots inside the disc provide good damping and contribute to quiet operation.
Inforce 11-01-095 (190x30 / 20 mm; 48 teeth) - clean cut plywood, particleboard, MDF, wood
MDF, chipboard and plywood are not very dense, but they can crumble strongly under the rough influence of equipment, so the disc should be as sharp as possible and it is required to cut at an average speed.This disk is equipped with 48 teeth and has a thickness of 2 mm, which ensures strength and evenness of the cut.
+ Pluses of Inforce 11-01-095 (190x30 / 20 mm; 48 teeth)
- There are four cutouts for expansion from heating.
- There is an adapter in the kit for installation on saws with a seat of 20 mm in diameter.
- Does not leave chips on chipboard.
- Do not bite into the material.
- Resistant to bending and deformation.
- Cons Inforce 11-01-095 (190x30 / 20 mm; 48 teeth)
- The adapter for installing the disk on a smaller shaft is glued to the back of the equipment - some users are scared at first that they did not put it in the kit.
- The quality of the soldering of the teeth is not even.
Conclusion. The model has tungsten carbine soldering, therefore it keeps grinding for a long time and provides a clean cut of pressed materials. The drive is optimal in terms of price and quality and is suitable for use in a personal carpentry workshop, but not for everyday use.
