Bulk floor Ceresit

The Ceresit brand belongs to the famous Henkel concern, which has existed for more than a hundred years. Ceresit bulk floors are a dry mix of high quality, packaged in waterproof packaging. A distinctive feature of the product is quick solidification. For example, the pour time of the Ceresit CN 175 is no more than 8 hours. Before buying, read the reviews and the Ceresit filling field, which will tell you about the features of pouring and subsequent operation.

Bulk floor Ceresit - reviews, ratings and recommendations

Ramil

Ceres CN 173

A comment

It perfectly aligns on layers of more than 5 cm and an area of less than 10 square meters. He leveled two balconies with reinforcing mesh, dried without cracks and perfectly even. I decided to fill them with the whole apartment - I grabbed grief! I did this: in four corners I drilled self-tapping screws, pulled a fishing line, immediately interfered with 10 bags, poured in and immediately leveled. Thickness 2 - 2.5 cm. Worked together. On the trail. the day almost cried. The rule put the differences up to 6 mm. The bumps had to grind grinder with a diamond cup. Now you have to wait until it dries, in order to further align.

pros

Price quality.

Minuses

It does not even at all on layers of 2-3 cm, dries quickly.

Term of use

more than one year

Recommendation to others

Recommend

Quality
4/5
Practicality
3/5
Price
5/5

Boxfon

thin-layer mixture Ceresit CN168 - quality is getting worse and worse

A comment

Lined the floors under the laminate last summer. Looked at an affordable price, and even on a promoted brand. As a result, the work, of course, was done qualitatively, but the time it took was an order of magnitude more than with another, more expensive mixture.

The only thing to complain about is the stirring. The mixture is stirred easily and quickly, until a homogeneous flowing mass without lumps. Evenly distributed over the surface of the base, the largest heaps are dispersed by a trowel, spatula or rule. Then, it is rolled several times with a needle roller to expel all air bubbles. The layer thickness was 0.5 cm. It dried quite quickly. Within a few hours I moved along the flooded floor on special studded soles, and the next day, carefully in slippers.

pros

cheap

Minuses

doubtful quality, it is necessary to level it in addition

Term of use

several months

Recommendation to others

Not recommend

Quality
2/5
Practicality
3/5
Price
4/5

Vobbler

Self-leveling quick-drying thick screed Ceresit CN173.

A comment

Last year, I had experience working with the Ceresit CN173 Self-Leveling Blend. The main condition was the drying speed, since pouring was carried out in the corridor 6-7 m, where all the doors of the apartment go. The mixture has quite controversial characteristics. With a maximum layer of 60 mm, the setting time is too short. One quality work is almost impossible. Alignment of the mixture takes a lot of time, despite proud positioning as self-leveling. If you work alone, you need to knead small portions in ¼ of the bag and observe the proportions of water precisely. Saturation of the solution with water is guaranteed to lead to the formation of cracks on the surface. The rule does not equalize it, too sticky and viscous.

pros

low cost, high strength

Minuses

inconvenient in work, requires strict adherence to proportions

Term of use

more than one year

Recommendation to others

Recommend

Quality
5/5
Practicality
3/5
Price
4/5

Koriss

Ceresit CN 69 thin-layer self-leveling mixture - problems with leveling large areas.

A comment

He leveled the floors throughout the apartment with Ceresite.Since the differences and defects were not very large, I chose the CN 69 thin-layer mixture. The preparation of the base was the same in all rooms - the primer, as recommended in the CeresitST 17 booklet, in two layers. Drying of the first 2-4 hours of the second before pouring for almost a day. First he poured a kitchen and a bathroom, the area of 11 and 7 m2, respectively. There were no problems with evenness or filling. The room was poured without additional markers or division into sections, in one layer up to 10-15 mm thick.

But when I proceeded to fill large rooms, then the problems began. Room is 26 m2. I dispersed the mixture with a polyurethane trowel, and then equalized it completely with a needle roller. Particular attention was paid to the joints of the layers. The surface was smooth, dense, without bubbles. When it froze a little, I applied the level and saw a difference of 10 mm almost always at the joints of the fills. I had to primer and add a layer

pros

good mixture quality, strong layer, good flowability

Minuses

Not

Term of use

more than one year

Recommendation to others

Recommend

Quality
4/5
Practicality
3/5
Price
5/5

Pestal

The leveling device for a floor of Ceresit CN175 - pretty high quality material for your money

A comment

He made custom repairs in the kitchen and in the hallway - leveled the floors. Took Ceresit CN175 as a budget option with good quality of a trusted brand. It was especially necessary to try in the corridor, since the kitchen should have tiles, and in the hallway and corridor there is laminate.

After dismantling the old coating, I processed the exposed plate of overlap with two layers of a deep penetration primer ceres ST17. The process itself is phased in as follows:
Knead the mixture, preferably the bag immediately, strictly following the instructions for the proportions of water. (that's why you need to use the entire bag at once, otherwise you can’t guess with water). The mixture is kneaded quickly and easily, without lumps and extraneous additives.

The finished solution is poured onto the base, and here the MOST IMPORTANT. You do not need to think that the solution itself will spread over the entire surface and lie evenly, but it must be leveled with a rule or a spatula. Despite the fact that he himself spreads quite well.

pros

Low consumption, good strength even in thin layers, good flowability.

Minuses

Not found.

Term of use

half a year

Recommendation to others

Recommend